InLoveArts 3D Filament Dehydrator EIBOS FilamentDryer for 4 rolls of 0.5kg filaments/2 rolls of 1kg filaments/1 roll of 3kg filament, Filament Dryer Box with Humidity Temperature Monitoring
- Independent humidity detector, digital display. The measuring range is 10 to 99%. When CYCLOPES is in operation, the humidity level in the box can be up to 10%.
- The drying temperature can be adjusted and the operation process is simple. The temperature can be set in a wide range up to 70 ° C.
- The basic components of CYCLOPES are made of flame retardant VO materials. A built-in temperature protection switch is also included ， automatic tripping in the event of overheating. This makes CYCLOPES even safer.
| | | |
|---|---|---|
8 sets of filament rack bearingsCYCLOPS uses 8 bearings to support the filament, the movement of the filament is more stable, and the pressure is stable. Can effectively avoid knotting and pinching the pressure wire. | Visualize temperature / humidity / timeThe heating time can be set according to your wishes, the countdown is set from 0h to 24h and it is switched off to the minute. You can also heat indefinitely. With this setting, CYCLOPES is in the normally open state. | Optimized heating methodThe hot air heating makes drying more efficient; Due to the unique air duct design, CYCLOPES corresponds to the principle of air thermodynamics and the filament is heated more evenly. |
| | | |
|---|---|---|
Memory setting parametersThe parameters last set can be saved automatically and are not affected by a power failure. | Dry & print at the same timeCYCLOPES can dry out during printing. A total of 8 holes are made on the shell to enable multidirectional outlets, which are suitable for using different types of printers or for using several printers at the same time. | Fire retardant materialThe core components of CYC LOPES consist of VO flame retardant materials. A built-in temperature protection switch is also included ， automatic triggering via temperature, making the CYCLOPE even safer. |
| Weight: | 2 kg |
| Dimensions: | 37.4 x 31.4 x 25.7 cm; 2 Kilograms |
| Brand: | InLoveArts |
| Manufacture: | InLoveArts |
| Reference: | MTEV1620978603789 |
It’s an expensive compared to other filament driers however it works! The 24 hour cycle it really useful it keeps your filament in great condition and recovers filament you would normally toss out, spend to save.
Ovvio utilizzo x essiccare a riscaldare moderatamente i filamenti in ingresso alla stampante, semplicemente utilissimo x trattare adeguatamente i materiali. Impossibile farne a meno.
Its dimensions are really big for a dryer but it does the job. I saw that the humidity inside goes down to 10% while the environment is around 80%. If the heated air would’ve been dissipated better with a guide, it would be better. But, I can print that 😀
just received the dryer and I’m quite happy with the performance. Put an old roll of TPU in at the recommended settings and it looks like it has removed moisture. I do have another dryer but its never been good for TPU (just doesn’t get hot enough) this unit has a heater that will go up to 70c as well as an exhaust fan to remove moist air, only down side is the noise, the fan isn’t the quietist and the heating control uses something that makes a clicking noise as it switches, its not so loud that its annoying but it is noticeable. the unit has quite a large footprint but so it can fit 2 1kg spools. i paid 69 for it as there was a deal on and at that price its a good buy not sure i would pay the full amount given the noise issues but its well made and dose the job would buy agai
As a result i decided to invest in a filament dryer. I researched quite a few dryers and settled on this ‘inlovearts’ one – mainly due to the fact i could dry and store two rolls of filament inside the dryer and the fact that it has an air circulating fan. Apparently this is a must to decrease humidity to an acceptable level.
The dryer requires very little assembly when you receive it – just a case of inserting the rollers in the correct place. There are several filament feeder holes around the acrylic lid which allow for a multiude of 3d printer options. The device is very simple to operate only require basic user input – time and temprature – these are very easily changed via buttons on the front of the device. The timer counts down and the device then switches off.
I dried two rolls of PLA for 4hrs at 50c and the total cost in electricity was 10p. The max draw from the device was just under 150w when the heating element came on.
On the front of the case is a removable humidity meter, you need to turn this on via a small push button located on the reverse of the display.
My only niggles with the device are that the humidity sensor easily pops out of the casing and the rollers for the filament are not secured in place, therefore they can fall out when moved – also the metal casters fall off very easily. I did find this slightly annoying – however if the dryer is placed in a permanent position then this would not be a major drawback.
Overall i am highly satisfied with this dryer and would recommend it to others.
I hope that you found my review helpful.
Des weiteren ein kleinen Lfter um Zirkulation zu erzeugen , denn ohne geht die komplette Hitze direkt nur an einer Stelle gegen das Fillament und es wird an der Stelle schmelzen, mit meinem Umbau wird das fillament gedreht und gleichmig erwrmt die Temperatur habe ich um 4 Grad erhhen mssen so ist im gesamten Gehuse eine gleichbleibende Temperatur da ich den kleine extra Lfter eingebaut habe und auf die mindestdrehzahl eingestellt habe.
Fr mich passt das so mit dem Umbau.
Da ich im Standard Backofen zu viel Energie verschwende und eine schlechte Temperaturregelung habe.
Ist der kleine trockner nun mit Upgrade Top.
Mon avis rapide :
+ super dvidoir
+ double rangement
– ne fait pas de miracle quant l’humidi
J’ai bien reu cette boite de schage de filament pour imprimante 3D.
L’ide d’avoir une boite de schage est inteligente car en schant les filaments j’obtiens de bien meilleurs resultat d’impression 3D. Sachant que le filament pour imprimante coute cher l’investissement dans une boite de schage me parais tre plus que ncessaire. La consomation de la boite est de 100W ce qui est raisonable le ventilateur extrait l’eau des filaments, ce n’est pas un pas un gadget.
Bon rapport qualit prix.
Livr dans un carton bien protg (mais difficile sortir de la bote).
L’assemblage est trs facile, les 4 tiges installer et insrer le tube silicone pour la sortie du filament pour distribuer directement sur l’imprimante 3D. Il y a plusieurs trous de sortie selon la disposition d’i,stallation.
Le rglage est trs simple, seulement respecter selon le modle de filament (PLA, ABS, etc..) il est indiqu la temprature et le temps de chauffe sur la notice en tableau.
D’une simplicit de rglage, et il fait son travail tout seul. La machine est un peu bruyant comme une imprimante 3D en chauffe. Sinon, son fonctionnement a l’air trs rgulier et fiable.
Dans cette bote, on peut mettre 2 bobines d’un kilo, c’est bien spacieuse.
C’est un produit complmentaire avec une imprimante en filament.
Pour les personnes ayant ouvert des filaments PLA depuis un moment, on connait tous cette dtrioration du l’humidit qui rends le filament fragile. Ici on a une boite de schage permettant de scher les filaments avant utilisation afin de diminuer le risque de casse pendant l’impression qui provoque un arrt et souvent on peut tout recommencer !
C’est un peu cher (120 tout de mme) mais l’effet est excellent, mme sur une bobine un peu ancienne (pas trop quand mme on va pas chercher les ennuis).
Permet de scher deux bobines en mme temps et permet galement de drouler le filament en fonction de l’impression, on a donc un filament sec et lgrement chauff, donc idal pour l’impression !
Je recommande avec plaisir, un produit parfait pour toutes vos impressions 3D !
Ultra pratique grce cette bote de schage c’est FINI les longs temps d’attendre de schage c’est beaucoup plus rapide et c’est un schage parfait. Ce que j’ai ador c’est qu’il y a un indicateur d’humidit qui permet de suivre le schage en temps rel. Cette bote de schage elle est vraiment top car premirement elle a une trs grande capacit grce son son grand espace qui permet d’utiliser quatre rouleaux de filament de 0,5 kg en mme temps ce qui est trs pratique. Ce qui est top c’est qu’on peut scher pendant l’impression ce qui permet un gain de temps norme et une meilleure impression car aucune dformation possible. C’est vraiment un trs bon rapport qualit-prix c’est super intressant d’avoir ce genre de bote de schage quand on a une imprimante 3D car a permet d’avoir un boulot parfait je la recommande sans hsiter.
permet d’avoir de proteger ou secher 2 bobines d’1 kg trs facilement (tester avec plusieurs marques et largeur, aucun soucis). indicateur d’humidit en facade trs pratique. controle en facade sur l’cran trs simple et lisible. taille optimal pour le sechage de 2 bobines, un peu bruyant avec le ventilateur.
J’imprime pas mal en filament, j’ai deux imprimantes cte cte.
Je dois avouer que je n’ai pas vraiment de souci de filament sec sur la SideWinder, mais avec la Creality, si je n’imprime pas pendant 3 jours, le fil casse encore et encore.
J’en ai profit pour essayer cette boite de schage qui permet, en plus de scher, de drouler le filament pendant l’impression.
Cette bote permet de stocker jusqu’ deux bobines de filaments, l’installation est trs simple car il suffit de placer les 4 barres en faisant attention bien placer les roulements billes et … C’est tout 🙂
Il est presque plus compliqu de faire passer le filament dans le trou pour alimenter l’imprimante.
Le fonctionnement est simple, la boite sche le filament en chauffant. Il y a un ventilateur sous la boite pour dispatcher la chaleur.
Il n’y a pas trop de bruit, sur la face avant de la bote vous trouverez un indicateur d’humidit.
Franchement elle trouve parfaitement sa place a ct d’une imprimante 3D, je dirais mme que si vous avez 2 imprimantes, elle aura sa place entre les deux pour scher deux bobines en mme temps 🙂
C’est vrai que c’est un peu cher (119 l’heure de ce commentaire) mais si vous avez le budget, a aidera conserver vos filaments !
L’humidit est l’ennemie numro 1 des filaments PLA pour imprimante 3D: les filaments deviennent cassants, ils augmentent de diamtre et peuvent se coincer dans la tte d’extrusion. L’impact sur la qualit d’impression est indniable. Mme si les filaments sont stocks avec soin, la meilleure des solutions est d’utiliser une bote de schage y compris durant l’impression, et c’est exactement ce que propose Eibos, une jeune socit chinoise de la rgion de Shenzhen avec “Cyclopes”.
J’apprcie les roulements billes des rouleaux sur lesquels reposent les bobines, et qui facilitent la rotation sans effets de celles-ci. La bote peut contenir deux bobines. Un tube tflon permet d’amener le filament sch directement l’imprimante 3D. Il est dommage d’avoir fourni un seul tube tflon, ce qui limite l’usage avec l’imprimante 3D une seule bobine. Fort heureusement, ces tubes peuvent tre trouvs par ailleurs, donc si vous disposez d’une imprimante deux ttes d’extrusion, il suffira d’acheter un tube tflon supplmentaire.
La notice propose un tableau qui indique les temps de schage ainsi que les tempratures en fonction des matriaux. Eibos a eu cependant la bonne ide de munir la bote d ‘un hygromtre permettant de dterminer le bon temps de schage ; un seul regret cependant, c’est que le bouton de mise route de l’hygromtre se trouve l’intrieur de la bote. Bien videmment, je vous conseille de l’utiliser galement comme simple bote de schage pour conditionner vos bobines avant stockage.
C’est une premire pour moi et pour l’instant, je n’ai rien de ngatif en dire.
Elle fait ce que j’en attends et c’est parfait !
J’ai essay de nombreuses box Dry.
Celle-ci est particulirement efficace et pratique.
Elle est pas optimum car le schage ne s’arrte pas seul et si elle est teinte, l’air rentre, alors l’humidit aussi.
Par contre, il y a un trs bon schage des bobines qui se fait, pas de transfo, un interrupteur et lorsqu’on coupe l’interrupteur rien dbrancher.
Trs pratique l’utilisation, prends les bobines Prusament.
Pour avoir test la S1 de Sunlu, la Esun est l et Eryone, celle-ci est la meilleure.
Je pense que c’est le must-have pour conserver un fil sec et une adhrence maximale , la boite permet de stocker les bobines dans les meilleurs conditions et peut servir de distributeur. La qualit de la base me semble un peu legere mais elle fonctionne parfaitement, avec un bruit raisonnable du ventilateur. Dans tous les cas je pense que ce n’est pas un achat inutile car la diffrence sur les impression est vidente.
This is missing element to get a perfect prints. I’m using it only with PLA material but should work with other stuff too. I was using silica gel bags but results from this is just another level. Great addition for any 3d printer, not the cheapest but definitely worth the money, if you have 3d printer you should have this as well. Absolutely perfect addo
Ender 3 V2 – in a Creality tent using a Microswiss All metal Hot-end – 04 Nozzle. Cura Slicer.
The main reason I bought as a last ditch effort to fix a couple of 1KG spools of eSun PETG I left out too long in a room with terrible humidity. The filament was printing with rough gravel texture, it was also distorting the color. I tried running eSun filament cleaner, turning up the hotend temp, turning down the hotend temp, new nozzle, new larger nozzle.. nothing fixed it.
I was quick to doubt this product like so many, after it’s first use I was disappointed. I set it to PETG and then waited the recommended time and sure it hit 10% and held it. Nothing changed in the next print after removing it while still warm from the unit and trying to print from it.
I instead weighed the filament to set a base line, then put it in the dryer on PETG for about 12 hours. 8 Hours then weighed it to see that a little weight did fall off, then a couple of more with slightly more weight reduction.
After giving it about 24 hours to sit in the dryer it stopped at a total of 2grams weight being removed.
I then printed from the spool while still in the dryer and ran a filament cleaner right outside the case just to remove an imperfections and it WORKED!!
Enough moisture removed I can print normally outside of the dryer now while in the tent full enclosed.
However, I much prefer to run the filament through the top of the tent using some filament cleaners and guides, it’s reduced nearly all my stringing and no delamination.
If packed away with a humidity pack while vacuum sealed should be good for long term storage again.
If used right, this could really save alot of money and really improve all compatible filament. PLA doesn’t have much moisture to remove so I wouldn’t really recommend to use for drying, but still works as a great storage unit.
Also, thing-i-verse has some prints just look up EIBOS, available is a spool attachment, filament track with bearings along with plugs for any of the filament ports that you want to block to keep the heat in.
It is good the only thing it could be better if it could take a 3 kilogram it’s too small for tha
Das Trocknen funktioniert gut und die Rollen sind sicher aufbewahrt. Einziges Manko, wenn man damit 2 Drucker mit Filament versorgt kann der Wechsel einer Rolle im Betrieb schnell etwas fummelig werden. Man muss dann aufpassen, dass man die andere Rolle in Betrieb nicht abknickt. Ansonsten tut das Gert was es soll und das sehr gut.
Very much satisfied with the EIBOS Filament dryer. It attains a maximum temperature of 65C and adjustable to, with the help of a 45W PTC heater which is energy-saving, long-lasting and environmentally friendly. There is a temperature knob that is used to adjust the temperature according to the different types of printing consumables. Whenever we want to pause the printing, all we need to do is just turn off the switch. The maximum capacity of the dryer box is 220*77 mm and works perfectly with moisture-sensitive filaments. It is provided with low noise turbofans. This will mainly absorb the moisture in the air which helps it to dry faster. Helps to printing fast and quality output too.
Fr ordentliche 3D Drucke braucht man neben einem geeigneten Drucker auch gutes und vor allem trockenes Filament. Leider zieht Filament aber mit der Zeit Wasser aus der Luft …
Frher musste ich deshalb mein Filament von Zeit zu Zeit im Backofen trocknen – jetzt nutze ich diese Box dafr. Die Box dient dabei zur Aufbewahrung und als Filamentspender fr den Drucker. Auf Knopfdruck kann ich jetzt aber das Filament ganz einfach in der Box schnell und zuverlssig trocknen. Das vereinfacht alles, verbesserte meine Druckergebnisse und funktioniert bestens.
As a regular 3D print enthusiast i have found varying issues with different types of filament, some of them were due to poor quality, however i found most of the issues actually came down to humidity levels either from how it was packaged or unfortunately how i have stored it since. I also have some colours that sit on the shelf for a while as they are rarely used on a full reel basis.
In order to combat this issue i now have this filament dryer, i use it as a one of boost to rescue some filament that has been used for a while, but also whilst running to ensure I’m not getting any of the dreaded bubbling or adhesion issues giving me consistent quality.
This works really simply in the fact that the filament reel sits on bearing rolls so it can move freely, i then feed the filament through directly to my printer meaning there are very minimal points where the filament could actually gain any humidity on the way to being printed, i then set the dryer really low whilst printing which gives another level or reassurance.
You do have a small amount of assembly when it turns up, however all that is is placing the rollers down onto the base and putting the tube on.
I did forget to show you the humidity monitor however that needs to be turned on from the inside and has extremely low power consumption so is not actually mains powered at all.
Overall, it has saved me the cost of at least 7 reels which i ultimately thought were lost, so well worth it.
I have a big fish tank in the same room as my 3D printer so there’s moisture in the air and it was effecting my printing until I started using this dry box.
It has a heater and a fan expelling air from the box and drawing air in and typically it gets the humidity inside the box to 10%. It’s easy to set the temp for different materials and once you get used to printing with it you will learn when you can turn the temperature down to save power using the humidity sensor to guide you.
I do most of my printing with PETG and the quality difference is day and night, the amount of blobs and stringing this has eliminated is very significant and the popping of water boiling as the filament leaves the nozzle has been eliminated.
I’d definitely recommend this.
Zeer tevreden over deze filament droger, heb gemerkt dat 3D printen lastig wordt als de vochtigheid de 50% benaderd en eigenlijk boven de 40% bijna niet te printen is. Deze filament droger zorgt in de kortste keren voor een vochtigheidsgraad van 17-20% en het printen verloopt een stuk makkelijker.
Zeer tevreden over deze filament droger, heb gemerkt dat 3D printen lastig wordt als de vochtigheid de 50% benaderd en eigenlijk boven de 40% bijna niet te printen is. Deze filament droger zorgt in de kortste keren voor een vochtigheidsgraad van 17-20% en het printen verloopt een stuk makkelijker.
J’ai achet ce box de schage car le passage en four n’est pas pratique et surtout le four n’est pas mon atelier (proximit).
La bote de schage arrive parfaitement emballe dans un carton sans dcor particulier, l’ensemble est maintenu par de la mousse, aucun souci au dballage.
La mise en service est simple, ont install les 2 supports de bobines (sur roulement), on branche et c’est prt fonctionner.
Le choix de temprature est large de 40 70 degrs, de mme que l’on peut rgler le temps de schage.
Les plastiques sont de bonne qualit, autant pour la base que pour le couvercle.
Il est possible (tube PTFE fournis) d’imprimer directement en sortie de bote, alors en plus de scher les bobines ouvertes depuis trop longtemps, on peut aussi chauffer les filaments en amont, ce qui permet d’imprimer vitesse plus leve, et cela n’est pas ngligeable.
Bon rapport qualit-prix
I have a mk1 ebox filament dryer and this has done quite well, but still over priced! And tacky.
The Eibu Filament Dryer seems to have a good sound working concept and it pumps out heat well and fast, I have managed to put 3 filament rolls in , side by side and runs that just fine.
My only quibbles are:
Quality, the bottom of the base is very thin, it moves and flexes if you fingers touch it, the base looks cheap too.
The display is basically a plastic overlay on top of the buttons, works just fine, but I can’t imagine it to last too long.
I don’t have much confidence in product, due to its build quality, I can only hope that the extra money went in to good electronics, but I doubt this is the case.
The hygrometer is very cheap, sits, when fitted at a slight angle to the body of the unit, the battery compartment feel like it would break when putting a battery in as it’s such a tight fit and the hygrometer, doesn’t work in conjunction with the temperature controller, it’s a very cheap and nasty separate unit the pushes into the acrylic/Perspex covering.
The only quality feeling parts of the device are the lid, this looks and feels of good quality.
The heating element, seems to do a good job and the fan isn’t too loud either.
It’s a good device that will do the job and do it well, but for how long, I have no idea.
But it certainly isn’t worth anything near the 139 they are asking for this, maybe in line with others ie50 to 70 mark is fair.
I’ve I were to buy this a again I wouldn’t want to pay over 60 for it.
It really doesn’t offer anything huge in any way to justify the extra cost, when compared to any other product in the market bar the ability to add an extra roll of filament or may an extra two filaments.
Only thing extra you are getting are:
Quicker heating when compared to other filament dryers.
Ability to add more then one roll of filament.
And a timer for you to set depending on what material you are planning on drying out.
There isn’t a lot of decent choices out there when it comes to filament dryers.
I have a mk1 ebox filament dryer and this has done quite well, but still over priced! And tacky.
The Eibu Filament Dryer seems to have a good sound working concept and it pumps out heat well and fast, I have managed to put 3 filament rolls in , side by side and runs that just fine.
My only quibbles are:
Quality, the bottom of the base is very thin, it moves and flexes if you fingers touch it, the base looks cheap too.
The display is basically a plastic overlay on top of the buttons, works just fine, but I can’t imagine it to last too long.
I don’t have much confidence in product, due to its build quality, I can only hope that the extra money went in to good electronics, but I doubt this is the case.
The hygrometer is very cheap, sits, when fitted at a slight angle to the body of the unit, the battery compartment feel like it would break when putting a battery in as it’s such a tight fit and the hygrometer, doesn’t work in conjunction with the temperature controller, it’s a very cheap and nasty separate unit the pushes into the acrylic/Perspex covering.
The only quality feeling parts of the device are the lid, this looks and feels of good quality.
The heating element, seems to do a good job and the fan isn’t too loud either.
It’s a good device that will do the job and do it well, but for how long, I have no idea.
But it certainly isn’t worth anything near the 139 they are asking for this, maybe in line with others ie50 to 70 mark is fair.
I’ve I were to buy this a again I wouldn’t want to pay over 60 for it.
It really doesn’t offer anything huge in any way to justify the extra cost, when compared to any other product in the market bar the ability to add an extra roll of filament or may an extra two filaments.
Only thing extra you are getting are:
Quicker heating when compared to other filament dryers.
Ability to add more then one roll of filament.
And a timer for you to set depending on what material you are planning on drying out.
I have used the same machine with different branding, so my review of this unit is the same!
I tend to use a small amount of a roll and then move onto a different colour, material or brand to test that so have quite a lot of partially used spools of filament lying around. Most of them are thrown back into their bag or box, but not sealed. The big problem is that they all absorb moisture and then are pretty much useless.
I tried running a print with one of the oldest spools and had nothing but failures. I popped the spool into this drying box and after about 5-6hours at 60 degrees, I was happily printing with the roll again.
The box fits two 1kg rolls quite comfortably. The fan seems to do a great job distributing the warm air and the bonus with this unit compared to cheaper models, you can print while leaving the spool in the dryer. The bearings feel smooth and the included Bowden tube is a decent length.
Happily recommend this unit if you’re like me and have loads of half rolls lying around wasting away.
I have used the same machine with different branding, so my review of this unit is the same!
I tend to use a small amount of a roll and then move onto a different colour, material or brand to test that so have quite a lot of partially used spools of filament lying around. Most of them are thrown back into their bag or box, but not sealed. The big problem is that they all absorb moisture and then are pretty much useless.
I tried running a print with one of the oldest spools and had nothing but failures. I popped the spool into this drying box and after about 5-6hours at 60 degrees, I was happily printing with the roll again.
The box fits two 1kg rolls quite comfortably. The fan seems to do a great job distributing the warm air and the bonus with this unit compared to cheaper models, you can print while leaving the spool in the dryer. The bearings feel smooth and the included Bowden tube is a decent length.
Happily recommend this unit if you’re like me and have loads of half rolls lying around wasting away.
Gerade fr eine groe Rolle (oder eben zwei kleine normale) ist diese Trockenbox wirklich praktisch. Wie bei anderen Herstellern auch kann man das Filament direkt aus der Box heraus verdrucken (was bei Nylon besonders praktisch ist). Auch die Einstellmglichkeiten (Zeit und Temperatur) sind nichts Besonderes und die Trocknung funktioniert wie erwartet gut. Was mir besonders gut gefllt ist die extra Anzeige der Luftfeuchtigkeit innerhalb der Box auf den Deckel. So kann man den Wert auch ganz wunderbar Ablesen und muss nicht vorher die gesamte Box einschalten.
Die Verarbeitung ist hervorragend und lsst hier keine Zweifel an der Qualitt aufkommen. Auch die Bedienung des Trockners ist kinderleicht und man versteht alles direkt auch ganz ohne Anleitung (Symbole fr An/Aus, Temperatur, Zeit, sowie zum Erhhen und erniedrigen des jeweils angezeigten Wertes).
Ich bin jedenfalls begeistert von diesem Filamenttrockner und kann ihn bedenkenlos weiterempfehlen.
Die Verarbeitung ist hervorragend und lsst hier keine Zweifel an der Qualitt aufkommen. Auch die Bedienung des Trockners ist kinderleicht und man versteht alles direkt auch ganz ohne Anleitung (Symbole fr An/Aus, Temperatur, Zeit, sowie zum Erhhen und erniedrigen des jeweils angezeigten Wertes).
Ich bin jedenfalls begeistert von diesem Filamenttrockner und kann ihn bedenkenlos weiterempfehlen.
Nachdem ich zuerst einen billigeren Filamenttrockner eines anderen Herstellers getestet hatte, den ich dann zurck schicken musste, weil er mein Filament nichtmal ansatzweise getrocknet hat, habe ich diesen Cyclopes Trockner bestellt und er funktioniert super.
Es passen zwei 1kg Rollen nebeneinander rein und durch das Geblse wird die warme Luft im Innenraum gleichmig verteilt. Zustzlich ermglichen die Wellen mit Kugellager auf denen die Filamentrollen im Trockner stehen, sowie der mitgelieferte PTFE Schlauch problemloses Drucken whrend des Trocknens.
Die Einstellungen der Temperatur und Zeit funktionieren wunderbar und deutlich prziser, als bei anderen Herstellern. Zustzlich kann man die Luftfeuchtigkeit im Innenraum berwachen, wofr aber leider keine Batterie im Lieferumfang vorhanden ist. Mein PLA, was sich vorher nicht mehr ansatzweise sauber drucken lies, konnte ich innerhalb von 5h bei 60C auf 10% trocknen und habe somit wieder sehr schne Druckergebnisse. Das gleiche auch mit Holzfilament oder PETG, wofr man die Temperatur auf bis zu 70C einstellen kann.