HUANUO Dual Monitor Wall Mount for 17 – 27 inch Screens, Wall Mounted Monitor Arm with Gas Spring Arm, Wall Mount Monitor Arm Support VESA 75/100mm, Load Capacity 3-8KG
HUANUO Monitor Wall Mount-Say goodbye to messy and crowed
At HUANUO, we focus on improving the strength and stability of the monitor arm. The dual monitor arm uses automotive-grade gas spring cores and has undergone 20,000 motion tests, which means it can be used continuously for at least 5 years of trouble free.
Positioning your monitor in the optimum spot has the potential to reduce eye, neck and back strain while improving your posture to make you more comfortable whilst you work.
| | | |
|---|---|---|
±45°TiltAdjust the angle of your monitor up or down slightly to provide you with the most ergonomic viewing angle. | 360° RotationThe left and right adjustment of the monitor screen allows you to share the screen with your friends in real time. | 180° SwivelThe horizontal and vertical screens can be switched freely to cater to your browsing habits. |
| Dimensions: | 35.56 x 22.86 x 10.16 cm; 4.13 Kilograms |
| Manufacture: | HUANUO |
| Origin: | China |
| Reference: | HNWDS1 |
PRO TIP FOR INSTALL!!! 43” off the ground is PERFECT For both sit and stand adjustability. I’m 6’ and my wife is 5’4” and we mounted identical setups @ 43” and we are able to have desk lowered to 31” for sitting and 40+ for standing. The mount says 32” monitor max but we got these Acer Nitro 34 curved on there. Given the angle of our desk we can keep them all flush YMMV.
PRO TIP FOR INSTALL!!! 43″ off the ground is PERFECT For both sit and stand adjustability. I’m 6′ and my wife is 5’4″ and we mounted identical setups @ 43″ and we are able to have desk lowered to 31″ for sitting and 40+ for standing. The mount says 32″ monitor max but we got these Acer Nitro 34 curved on there. Given the angle of our desk we can keep them all flush YMMV.
They look nice and support two monitors as advertised. However the 2 bolt holes at the top of the plate are left and right of center and the lower bolt hole is centered on the plate, so you can not actually mount it level on a wall stud and have to compensate for it in the height and alignment of your monitors. Other than that it's does the job well.
They look nice and support two monitors as advertised. However the 2 bolt holes at the top of the plate are left and right of center and the lower bolt hole is centered on the plate, so you can not actually mount it level on a wall stud and have to compensate for it in the height and alignment of your monitors. Other than that it’s does the job well.
This armature gets the monitors off the rolling desk and enabled me to install them on the wall next to the closet. I now have the computer, both printers, and speakers in the closet and out of sight.
This armature gets the monitors off the rolling desk and enabled me to install them on the wall next to the closet. I now have the computer, both printers, and speakers in the closet and out of sight.
It's hard to visualize/understand how things are going to look once the monitors are up and in various positions (depending on their size), but I could have easily bought larger montitors ( got 2 Septre E24 monitors), and they would fit side by side pushed back towards the wall.
It’s hard to visualize/understand how things are going to look once the monitors are up and in various positions (depending on their size), but I could have easily bought larger montitors ( got 2 Septre E24 monitors), and they would fit side by side pushed back towards the wall.
Very happy with this mount. It works exactly as described. The cable management system is great and it's sturdy. As mentioned in other reviews, expect that 27" monitors will stick out from the wall a fair bit if you want the bezels to touch like I did. This is just due to the geometry of the arms/vesa mount and you can't do anything about it - I would expect that the distance from the wall will decrease as you increase the monitor size. For reference, my pictures are of two 27" curved monitors with the bezels touching.
Very happy with this mount. It works exactly as described. The cable management system is great and it’s sturdy. As mentioned in other reviews, expect that 27″ monitors will stick out from the wall a fair bit if you want the bezels to touch like I did. This is just due to the geometry of the arms/vesa mount and you can’t do anything about it – I would expect that the distance from the wall will decrease as you increase the monitor size. For reference, my pictures are of two 27″ curved monitors with the bezels touching.
I mean I got what I paid for. It wasn't the most expensive mount. The gas arms work well, while the adjustments are a little finicky. My biggest gripes are the monitor mounting hardware didn't come with the proper dice spacers, and the physical mounting of the monitor to the arm. When you mount the monitor to the arm it's very loose and sloppy with a single set screw on top that you can tighten all you like, but doesn't make the system any more rigid.
I mean I got what I paid for. It wasn’t the most expensive mount. The gas arms work well, while the adjustments are a little finicky. My biggest gripes are the monitor mounting hardware didn’t come with the proper dice spacers, and the physical mounting of the monitor to the arm. When you mount the monitor to the arm it’s very loose and sloppy with a single set screw on top that you can tighten all you like, but doesn’t make the system any more rigid.
Capable dual monitor mount with a minor limitatio
I needed a convenient work from home space but didn’t want a desk cluttered with cables and monitors. This monitor mount was the ideal solution for keeping my desk space clear and allowing me to work in several configurations.
I definitely recommend mounting to a stud if you are able. I strongly discourage anyone from using drywall screws with this product. You would be far better off using toggle bolts if you can’t mount to a stud.
My only complaint with this product is there doesn’t appear to be a way to adjust the horizontal shift of the monitor position leaving a gap between my screens.
To push the monitors together I have to bring them to where they sit too far forward where it’s a little too close for comfort—although it’s a plus if you slouch while working because if forces you to sit back.
I would appreciate if there was a bracket or some additional accessory available that could make this functionality possible.
Even so, I’ve found numerous comfortable positions for working but nothing that centers both screens. I’ve found other wall mounted solutions that do offer horizontal adjustment but they were several times more costly at $200+.
All in all this is a good product that functions well.
Get monitors off your desk; adjustable
Installing the mount at the correct height can be tricky, so don’t drill holes in your wall until you figure that out. A general rule is to attach the mount to the wall so that it’s about halfway from the bottom of your monitor when at the height that’s most comfortable for viewing. The monitors stick out about a foot from the wall. Very adjustablable.
Attaching the plates to the back of monitors then sliding on the arm mounts is easy.
It took us about 30 minutes to install because we made some adjustments (and we weren’t in a big rush).
Yes, your cords will show.
The installment was easy and mount it’s self was built well. The only issue was the screws that were brought along where horrible quality I used a regular screwdriver and I completely shredded it. I had to go to a hardware store and buy replacements. Very poor quality.
The installment was easy and mount it’s self was built well. The only issue was the screws that were brought along where horrible quality I used a regular screwdriver and I completely shredded it. I had to go to a hardware store and buy replacements. Very poor quality.
Does the job good enough
This is my first vesa mount so my problems could be the same with others. Pros
Cheap
Good wire management
Good build quality
Easy to set up
Cons
Screws are garbage stripped very fast luckily I had the correct socket so I diddnt need to go out and buy new ones
Micro adjustments suck I cand get my monitors in the exact position I want
This is a cheap vesa wall mount so I understand why I can’t get perfect placement. Thr only reason why it’s 4* is due to the screws I understand they are trying to save money but I’d be fine paying another $5 for better quality screws and possibly heavy duty drywall anchors.
See below :-)
Ideally you need to hold the monitor where you want it and adjust everything in place.. Having someone hold it exactly, where you want it is ideal.. We were trying to install this above the desk, not easy to hold a large monitor in place, adjust it and reach around to secure it tightly in place.
Very good quality, easy to mount so a 5-star on that.
Ich habe die Monitor Wandhalterung fr zwei Monitore gekauft und war grundstzlich zufrieden damit. Die Halterung ist sehr stabil und hielt meine beiden Monitore sicher an der Wand. Die Gasfeder ist einfach zu bedienen und ermglicht eine einfache Einstellung der Hhe und des Neigungswinkels. Die Halterung ist auch drehbar, was es mir ermglicht, meine Monitore in verschiedene Richtungen zu bewegen. Der einzige Nachteil ist, dass die Halterung viel Platz einnimmt, was sie fr kleine Rume ungeeignet macht und weshalb ich Sie letztlich wieder zurck gesendet habe.
Genau was ich gesucht habe.
Das Produkt hlt was es verspricht und hat dazu einen sehr guten Preis. Man kann seine Monitore drehen wie man will und die Qualitt und Stabilitt dabei ist hervorragend. Zu diesem Preis gibt es keine vergleichbaren Produkte. Empfehle ich weiter.
We purchased this mount to use with a platform that elevates to turn a standard desk into a standing desk. This mount has a greater range of motion than any other wall mount that I could find which is key considering the platform has about double the range of motion. So finding the correct mounting height to work in both low and high positions is key. I found the adjustments to be very easy and was able to tighten things up so it holds the monitors in the correct position but still allows easy lifting and lowering thanks to the gas struts. My wife switches between standing and sitting more than a dozen times a day so this is the most important aspect of the mount. The only reason I don’t give it 5 stars is because the cable management pieces just didn’t stay in place when raising/lowering so we ended up discarding them and using zip ties instead. If they had made the covers attach to the base more securely then this would easily be 5 stars.
As others have stated, the monitors have a gap between them when pushed all the way back to the wall. We knew this going in thanks to the many reviews and were fine with that. We were looking for a low profile solution for a home office that pulls double duty as a spare bedroom and the gap doesn’t bother my wife.
Gute Halterung für 2 Bildschirme
Reggono pure mia mamma
Sono robusti e reggono 2 monitor da 27 pollici , un po’ male per regolarli , perch hanno bisogno dell’esagonale ed scomodo sopratutto se gi tutto attaccato per il resto top materiali ecc
Sturdy mount, mildly annoying mounting hardware
I have previously owned a desk-mounted Huanuo monitor arm and needed to switch to a wall-mounted setup. I owned the desk-mounted arm throughout the interminable Covid pandemic and it was great, so naturally I chose to stay with Huanuo for the wall mount.
The arm itself is excellent and I recommend it—it’s just as good as the c-clamp desk mounted version. I have two 24-inch monitors attached.
Installation was fine. Given the reviews, I was expecting to need to draw my own template and purchase additional mounting hardware, but as it turns out they have added a precut template and more mounting hardware to avoid these issues. That was a pleasant surprise and I am glad to see Huanuo responds to customer feedback.
I experienced two issues: One of my own making and one inherent in the product, First, I did not realize this mount was not compatible with steel studs. Many new build apartment buildings use steel studs instead of wood studs because of their fire resistance (along with other nice features). Because steel studs are typically narrower than wood studs, and because toggle bolts require approximately half inch holes to mount, I did not see a way to sturdily attach the mount to the steel studs without an uncomfortable chance of accidentally cutting one face of the stud in half with the drill bit. This was my own fault.
Instead I anchored a 4.5 foot fence post to a concrete block and fastened the monitor arms to post. This, while not the prettiest thing I’ve ever made, is working fine. In doing so, I discovered that the provided lag screws are not of great quality. The manual recommends installing with them a socket wrench, but this would be a giant PITA, so I first used a socket adapter in my drill to get them most of the way in and then hand-tightened at the end. There is no way you’d be able to use a standard Phillips head drill bit without stripping the provided screws.
Even with the socket adapter, the provided lag screws barely got in—the screws are quite soft and the indent that marks where the screws are fastened means you get maybe a quarter inch of grip on the head to drive it into the wood. This is a pain but not a disaster—I would recommend just buying your own lag screws of comparable size (size given in manual) and use those instead.
Additionally, a very minor annoyance is that one of the thumb screws meant to keep the monitor in the bracket was a little too large (the other fit perfectly). I think its something like a #6 machine screw; I had something lying around that fit and used that instead. No biggie.
tl;dr: great mount, subpar mounting hardware but that is easy to get on your own.
I bought these for my home office, very easy to install and use. The best part is how affordable it is.
I bought these for my home office, very easy to install and use. The best part is how affordable it is.
Better for thick walls.
Brought this to expand my set up, the walls in my house tend to be on the thinner side and you’d need special wall plugs to really get it sturdy and in my case it definitely could be sturdier but does the job.
The arms themselves are somewhat stiff so if your expecting smooth gliding motion it’s not always the case depending on the direction, some shake in there but they have worked well for swinging a monitor over to my desk. Tilting them up and down you’ll need to loosen them so you can’t always just do that on the fly. They do the job I needed them for, may replace them with a different type of set up in the future.
Its an excellent bracket. The problem I have is that in order to position the two monitors next to each other they are too close to me to focus. They should have made the piece that attached to the monitor that could slide on the arm. Or make that arm telescopic.
Its an excellent bracket. The problem I have is that in order to position the two monitors next to each other they are too close to me to focus. They should have made the piece that attached to the monitor that could slide on the arm. Or make that arm telescopic.
Not difficult to setup. I have been using my two 27' monitors monitors for a few months now. No issues.
Not difficult to setup. I have been using my two 27′ monitors monitors for a few months now. No issues.
Good but not as good as having two separate poles mounts
This is ok, but in my view attaching two monitors on a two arm single point mount is always going to be slightly flawed as there are only so many places that the monitors will sit nicely together and you can be guaranteed that these won’t be quite where you need them. Do yourself a favour and buy two separate pole mounts.
Solid if a little bulky
Doesn’t sit flush to the wall with 2 monitors attached but gives a wide array of possibilities through its felxiblity
Supporto Monitor x pc
Perfetto x la gestione di 2 monitor. Permette di posizionarli come si vuole
Besser als erwarte
Diese Wandhalterung hat mich total berrascht. Angesichts der nicht all zu groen Auswahl an Doppelwandhalterungen und dem relativ gnstigen Preis waren meine Hoffnungen auf ein Qualitativ hochwertiges Produkt eingeschrnkt. Doch als die Halterung ankam war ich schwer beeindruckt.
Positiv:
– saubere Verarbeitung, stabiles Material und hochwertiger Eindruck
– verstndliche Anleitung, Schrauben und Dbel sind dabei
– ich habe zwei unterschiedliche Bildschirme montiert, einer leicht, der andere etwas schwerer. Beide halten sofort, ohne Schwanken auf jeder einstellbarer Hhe. Die Hrte der Tragkraft ist an einer Schraube einstellbar. Bei einem leichten Bildschirm wird die Feder (oder der Spannmechanismus) natrlich nicht so hart eingestellt als bei einem Schweren Bildschirm. Die Range der Einstellbarkeit ist relativ gro.
– der Preis bewegt sich im Bereich der einfachen Wandhalterungen, daher Top
– die wichtigen Gelenke kann man fester oder lockerer Einstellen
– die Halterungen sind seit drei Monaten im Einsatz und sind wie neu
Negativ:
– Montage: Das Teil macht einen hochwertigen und massiven Eindruck, das ist es auch. Es wiegt einige Kilo. Ich hab die Montage alleine gemacht, es empfiehlt sich aber, die Montage zu zweit zu machen. Die Arme sind in der Horizontalen an drei Gelenken beweglich, in der Vertikalen an zwei Gelenken (Gelenk der Bildschirmauffassung mitgerechnet). Das macht die Halterungen insgesamt sehr sehr unhandlich. Eine Montage alleine erfordert Geschicktheit, Ausdauer und Geduld. Bei mir hat es funktioniert, jedoch war die unterste Position der beiden Bildschirme am Schluss leider etwas hher, als ich erwartet hatte. Aber nicht weiter tragisch…
– Aufgrund des Gewichts und der ntigen Einstellungen an der Spannhrte der Arme ist es nicht wirklich mglich, die Halterung samt Monitoren an die Wand zu halten um die ideale Anbring-Hhe testweise zu begutachten.
– an jedem “Arm” ist ein schwer lsbarer gelber Warnhinweis-Aufkleber, etwa vier auf drei Zentimeter.
Fazit:
Wrde ich jeder Zeit wieder kaufen, der Preis ist absolut gerechtfertigt.
Ideal wre es, wenn ein kleiner Hinweis fr die Anbringung der Bohrungen in Bezug auf die untersten bzw. der obersten Position der Bildschirmfassung (eventuell auch Spanne rechts und Links) angegeben wre (die unterste Hhe der Bildschirm-Unterkante bzw. die oberste Hhe der Bildschirm-Oberkante wre natrlich noch genialer, aber da gibt es bekanntlich unterschiedliche Gren und Lngen). Dann knnte man die Position der Schrauben an der Wand realistisch abschtzen ohne dafr das Teil samt Monitoren mit einer Hand an die Wand halten zu mssen und mit der anderen die Bildschirme die Bildschirme in verschiedene Positionen ausrichten. Dann wre die Montage auch alleine machbar und man erhlt ein Einwandfreies Ergebnis.
Positiv berrascht hat mich die zuverlssige Einstellbarkeit fr unterschiedliche Bildschirmgewichte. Die Bildschirme halten zu dem perfekt in ihrer Position.
Klare Kaufempfehlung
This mount is amazing!! Very well built, I like the fact that is overbuilt. Large mounting plate for wall, large pivots, gas shocks, and sturdy metal arms. Packaged very well, all the hardware was included as well as tools for torquing the shocks and installing monitors. Great product.
This mount is amazing!! Very well built, I like the fact that is overbuilt. Large mounting plate for wall, large pivots, gas shocks, and sturdy metal arms. Packaged very well, all the hardware was included as well as tools for torquing the shocks and installing monitors. Great product.
This wall mount is very well built, and with the monitors suspended, I have much more clear work space! I have a 34" LG 34UM59 LCD ( actual width 32.5") and a 27" ACER S271HL LCD ( actual width 25.25" ). I tightened the gas piston for the 34" LCD and it holds perfectly. I didn't like the idea of mounting it directly to the wall, so I mounted it to a 2 by 6. I used 3/8-16 cap screws 1.75" long. This required re-drilling the mounting holes slightly oversized to fit the bolts. Then I used 3/8-16 "t-nuts" through the back side of the 2 by 6. Once I hammered in the t-nuts, I mounted the 2 by 6 to the stud, using lag bolts, placing it flush on the desk to help support weight. The wall mount is then bolted on. One thing to mention is to mount the HUANUO down low near the desk. I have shelves which are 23" above the desk. The monitors can move the full vertical range. The attached picture shows the monitors side by side when pulled out as far as possible.
This wall mount is very well built, and with the monitors suspended, I have much more clear work space! I have a 34″ LG 34UM59 LCD ( actual width 32.5″) and a 27″ ACER S271HL LCD ( actual width 25.25″ ). I tightened the gas piston for the 34″ LCD and it holds perfectly. I didn’t like the idea of mounting it directly to the wall, so I mounted it to a 2 by 6. I used 3/8-16 cap screws 1.75″ long. This required re-drilling the mounting holes slightly oversized to fit the bolts. Then I used 3/8-16 “t-nuts” through the back side of the 2 by 6. Once I hammered in the t-nuts, I mounted the 2 by 6 to the stud, using lag bolts, placing it flush on the desk to help support weight. The wall mount is then bolted on. One thing to mention is to mount the HUANUO down low near the desk. I have shelves which are 23″ above the desk. The monitors can move the full vertical range. The attached picture shows the monitors side by side when pulled out as far as possible.
Usata per doppio monitor da 28 pollici
L ho utilizzata per posizionare a parete i miei 2 monitor da 28 pollicila staffa semplice da montare e permette parecchie regolazioniunica pecca che per avere i 2 monitor vicini bisogna metterli parecchio in fuori dalla paretese si cerca in installazione vicino alla parete coi 2 monitor vicini vicini non L ideale
Excelle
I purchased this duel monitor support system because a desktop stand on one of my monitors failed completely, without any action on my part; it just broke. So, I was looking to upgrade to a duel monitor system which would not require mounting to the desktop; my desktop is glass.
I ordered this 2 days ago; it arrived yesterday evening.
After a light review of the instructions, and knowing how to properly mount things on a stud behind drywall, I went to work. Taking advice of the person who recommended a cardboard template, I created one from the cardboard within the shipping box itself. I used a stud finder to find and mark the outer boundaries of the stud on the wall. I used a level to mark a line for the placement of the cardboard template. I drilled pilot holes as the template had been marked accordingly. I used an electric drill to drive the hex cap lag screws into the holes, with the mount held against the wall. I attached the mounting bracket to the monitors and slid them into the arms. Note: you may have to loosed the final joints on the monitor arms to allow for easier movement in the up/down direction; not too loose, not too tight. I placed the cables in the bottom arm channels with removable covers.
The system is now in place. about 30 minutes to complete install. It is well designed. It is well worth the price asked. You will not be disappointed.
The screws which ho9ld the monitors to the arms were not in my package. As weight alone holds the monitors in place this was not a great concern. I may go to the hardware store and obtain hand turn screws to insert into these holes just to assure firmness of the joint. The monitors can wobble slightly without them; no big deal as they would not wobble when not being moved.
So, if you need to mount two monitors to a wall, this is a very good way to do it. Buy one and see for yourself…
hatte mir diese Halterung bestellt da ich meine beiden Monitore schn an die Wand hngen wollte. Allerdings habe ich dabei die Wand nicht gefragt. Als das Teil ankam, schaute mein Mann mich an, dann die Wand und meinte ob ich meinen Tisch in den Keller haben wollen wrde, denn im Bro haben wir nur Leichtbauwnde. Das Ding an sich wiegt schon einiges und dann noch mit zwei Monitoren dran. Das wre zu viel gewesen, daher ging es leider zurck.
Preis passt allerdings zur Qualitt. Htte es echt gern genutzt.
I've been using it for over a year now still as sturdie as it was when it was setup. Perfect for my dual monitors
I’ve been using it for over a year now still as sturdie as it was when it was setup. Perfect for my dual monitors
Perfect for my gaming set up
I did a lotttttt of looking around and ended up with this mount for my monitors (Two 27″) the arms are extremely solid, overall mount construction also extremely solid. Arms move any way you can imagine and my screens line up perfectly straight. 10/10 would buy again.
Try and get help hanging it. The mounts very heavy and was a pain in the @$$ to hang along, not impossible, just not fun until you get one screw all the way down to keep it holding itself
Supper easy to install, though I did find the lag bolts they provide a bit overkill. Very nice looking and lots of optional positioning
Supper easy to install, though I did find the lag bolts they provide a bit overkill. Very nice looking and lots of optional positioning
Hervorragend für ein Dual Setup
Im Lieferungsumfang sind der Arm selbst und die fr die Montage bentigen Schlssel ordnungsgem und ordentlich verpackt. Bei der Montage selbst empfehle ich eine zweite Person hinzuzuholen da dass dann doch eine ziemliche Fummelarbeit war. Das Teil ist sehr robust und hlt 2x 27 Zoll Monitore Mhelos oben, am Arm selbst ist der Gasdruck entsprechend leicht und mhelos einzustellen.
Robust method to mount your monitors
There’s no mistaking that this item is solid and well built, also relatively heavy. Following the instructions, I located the wooden stud within the wall and marked the centre. The instructions then said to hold the unit against the wall, hold a spirit level to the top and to mark your holes to drill, doing this on my own was impossible as it’s so heavy that there was no way I could hold it with one hand and mark with the other. My only other gripe was with the lag screws, trying to use a screwdriver or impact driver on these was impossible, I stripped all three screws even after drilling larger pilot holes than the instructions suggested, I’d highly advise have an M6 socket or box spanner handy to get these into the wood.
The adjustability is amazing! Up, Down, tilt, twist, left, right. I did have to adjust the gas struts but not a big deal.
It was a good mount easy to use I would recommend and get another one if I had more mounts
It was a good mount easy to use I would recommend and get another one if I had more mounts
easily supports a 24-inch monitor….you can adjust its hardness, height and position, I would buy it agai
easily supports a 24-inch monitor.you can adjust its hardness, height and position, I would buy it agai
Rapporto Qualità-Prezzo incredibile! uno dei migliori in assoluto.
Rapporto Qualit-Prezzo incredibile! uno dei migliori in assoluto. Facile e veloce da montare, qualit dei materiali di alto livello e robustezza unica. Ottimo prodotto! Molto snodabile e facile da utilizzare e modificarne la posizione. Utilizzato per due monitor curvi da 27 pollici
Excellente qualité!
Facile d’installation, ce produit rpond entirement mes attentes et est trs pratique.
Great but...
Great quality product with attention to detail.
Pros:
-Sturdy
-Well Build
-Cord organizers built in
-Strong adjustable springs.
Cons:
– When you use the 27inch monitors you loose almost all your range of motion. The arms can hold them, but the only adjustment you can make without them overlapping is up and down motion.
Excellent support double
Un excellent support pour deux crans au format standard VESA 100/100.
Les chevilles pour le bois et la briques sont fournies mais rien pour le placo videmment : il faudra prvoir de petites (mais pas trop) chevilles.
Le rglage en hauteur se fait par rglage de la tension en fonction du poids de l’cran.
On positionne ensuite comme on veut l’emplacement.
Prvoyez d’tre deux pour un positionnement correct car le support est en fer et donc assez lourd en plus d’tre encombrant.
Trs content en tou