Creality 3D Printer Enclosure Fireproof and Dustproof Printer Tent for Ender 3 / Ender 3 Pro/Ender 3 V2/Ender 5 Pro, Constant Temperature Protective Cover Room Storage 445x565x685mm
Compatibility
Small Size (445x565x685mm): Ender 3/Ender 3 Pro/Ender3 V2
Large Size (750X700x900mm): Ender 3 Max/Ender 5/Ender 5 Pro/ Ender 5 Plus/ CR-6 SE/CR-10 V3/CR-10 S Pro V2/ CR-X/CR-20/CR-20Pro
Customer Services
- Our after-sales technical team will provide you with detailed solutions within 24 hours.
- We will be devoted to producing high quality products & providing better service.
| Weight: | 2.57 kg |
| Size: | S |
| Dimensions: | 69 x 16.5 x 10.5 cm; 2.57 Kilograms |
| Part: | EU6-ZGZP-S |
| Batteries Required: | No |
| Batteries Included: | No |
| Manufacture: | Creality 3D |
| Dimensions: | 69 x 16.5 x 10.5 cm; 2.57 Kilograms |
| Reference: | EU6-ZGZP-S |
| Size: | S |
I purchased this enclosure as I was experiencing adhesion issues when running my Ender 3 v2 Neo a cold room; this seemed to offer a cheaper solution that turning up the heating. Well it works better than I expected; where in the past I would have needed to print on a raft I am now, in most cases, able to print abs and petg without any adhesion constructs.
Although it requires a bit of wiggling to get my Ender 5 Pro in the medium sized enclosure, once in I found there was plenty of room to setup and use the printer.
It is awkward to change the spool but as that’s not very often I don’t mind. It overlaps the little ikea table every one seems to use by a few centimetres but not enough to cause a stability issue.
Overall I am very happy with it, as the printer is in an outbuilding I had so many failed prints when the temperature dropped. Well, not anymore my prints are so much better quality and not one failed print. With a blanket on top the temperature stayed around 25 C.
Perfect size for ender 3 V2 and great quality can’t complain!
Used for Ender3 v2 neo. Keeps the temp stable. Used in cold garage. No problems with printed results. Good quality.
This made a big difference in my prints. I haven’t had any print failures as without it i use to have warping on the build plate and failures due to change in temperature…i would highly recommend it.
Had trouble with failed prints in my house due to drafts and temperature fluctuations. This solved these but I did have to modify it for my printer. Should be OK with an Ender though.
Bought for an Ender 3 Neo and fits fine, tall enough to house a 1KG spool. Happy with purchase.
Does help with adhesion but mainly helps stop the dust in the air produced by the printer. Not sure what it was with my Ender 3 V2 but after few hours it always seemed to feel dusty in the air when in use, after all there is super fine partials produced by the printer. Now the printer is inside this enclosure it definitely feels better in the room. It has cut down the “feel” of the dust in the air/better air quality.
I also run an air purifier close to the enclosure to help also. A must if you have an Ender 3. Can’t give it 5 stars due to its size. It is quite big, it could have been slightly smaller, it’s also a dust magnet on the outside.
Will update this review further down the line.
For a small its big.
I have an ender 3 inside.
So easy to assemble and fit cover on.
Holds temp well i have a digital thermometer and its 36 most times.
Would recommend put a light in it as its dark to see inside.
Worth the price and good value.
Im happy with i
For me is the cheapest solution.
My Aquila x2 fitts well.
I bought this for my Ender 3v2. It was bigger than I expected but it should help with better prints. Easy to assemble once I worked out the cover alignment. The power lead aperture is on the wrong side but that’s no problem. There’s lots of room inside and although it looks quite chunky in the room, actually it’s not vastly bigger than the dimensions of the printer. It could do with being a tad shorter but it’s perfectly livable with. As a 3D printer enclosure it is excellent value and will fit many printers. I recommend it.
The enclosure was easy to assemble and has plenty of space for my ender 3 pro. I can finally print abs without warping and layer separation now with this enclosure!
I used with a Prusa Mk3. It is bigger than you actually need for such a printer, but it does mean that you have easy access for maintenance etc
The material is very odd, it’s almost sticky. The listing claims it is fireproof, I would be SHOCKED if that is true.
Easy to assemble and seems sturdy. Fits my Creality Ender 3 in it no problem. A useful pouch on the side and slot for allowing mains plug out as well. I recommend it even though it is a tad pricey.
The enclosure unit is expensive for what it does, also there are many issues with the seals on the unit I received resulting in having to tape it up. Overall I would probably do one in perspex next time to ensure the seal was better would recommend it for a beginner.
Luckily I have the room for it and have built a dedicated table for it.
This is massive, but for me its worked out really well as My Ender 3V2 is heavily modified. and its given me the room inside the tent to accommodate all my mods, custom top mounted spool holder for direct drive, keyboard for octoprint my printers rarely off so its also allowed me to store all my PETG inside at 35’c 22% humidity, which is what my tent seems to levels out at when in use and zipped up.
The window takes a while for the creases to fall out, but they will making the window much easier to see through.
Its very easy to assemble, the quality of mine is very good, all stitching and zips are well constructed in the right places of corners.
It has created a stable temperature printing environment, has also helped me to prevent some corner lift/warping on large surface area, longer printing models as i print in PETG Nylon and CF filaments.
I really like the enclosure, bought 2 now for my machines. I get better prints because the heat is contained and more consistent where my printers are in drafty garage.
It’s just a shame the opening flaps position is such that operating the printers controls is awkward. Would have been better to open up the front and not the side.
Fits printer well with plenty of room for access and spool. Feels durable and good quality. Comparable to ones twice the price. Would recommend using side access flaps to pipe in ventilation for main board and power supply as it gets warm in there. Perfect for printing ASA/ABS or just keeping dust off the printer. Seems to cut out noise well, but is dark inside without some LED lights fitted to the printer (which is very easy to do).
Diese Bauraumabdeckung ist echt ihr Geld wert!
Jetzt kann mein Ender 5 plus im Keller stehen. Die lauten Lfter stren nicht mehr und die Bauteile knnen perfekt gedruckt werden auch bei 12C Umgebungstemperatur (Keller). Dadurch knnen meine Bauteile ber Nacht drucken und ich habe weniger Probleme mit Warping und Druckbetthaftung.
Die Qualitt ist sehr gut und die Funktion wird voll erfllt. Die Reiverschlsse sind absolut in Ordnung und die Nhte ebenfalls. Trotz meines groen Druckraums (Ender 5 plus) ist mehr als genug Platz in dem Zelt brig (Gre L).
Rundum zu empfehlen, den Platz fr den groen Kasten muss man aber erstmal haben 😉
Plus grand que ce que je pensait mais parfait reste plus qu’ essayer une impression dedans
Eignet sich gut damit auch Drucke in kalter Umgebung mit konstanter Temperatur in dem Zelt gute Ergebnisse liefern. Das einzige Manko ist der Preis.
I got the larger one because it said it would fit the max, etc, which has the same footprint as the CR10 Smart, so I figured it would fit a CR10 Smart… it does… kind of?
Physically, it will fit inside it, yeah – fine, but try actually using the bloody thing while it’s inside, because you will need patience and a buffer zone around the enclosure because stuff is going to be poking into the sides of the enclosure most of the time… it does the job though, keeps the warm air in a decent job of keeping the humidity low.
Great produced if anything a little big but prints abs now with no problem at all
Works great!
If I had known this earlier I would have bought one a long time ago.
As the nights get colder now, overnight prints are having delamination. Bought the kit to keep the heat in, and it works perfectly well. Improved print quality dramatically. The sound reduction isn’t massive, but it does make a noticeable difference.
Positiv:
Sehr einfach aufzubauen
Keine Mngel im Material oder Verarbeitung
Negativ:
Fr den Ender 3 v2 ist es etwas sehr knapp bemessen.
Er passt, aber die Steuereinheit muss leicht an die Wand gedrckt werden damit der Stepper die gegenberliegende nicht berhrt.
I, like you, make things myself, hence we are printer owners. The temptation is therefore to build your own enclosure, however given I have limited time I decided to try this ready made one.
There isn’t much to fault. It goes together easily, is as sturdy as you’d expect and has openings in all the right places (this review is for the large version for a CR10S Pro). There’s even an outside pocket for all those tools you keep losing.
Be aware that (at time of writing) the picture on the Amazon site has the depth and width dimensions swapped – it’s 750 mm front to back, see the picture attached to this review.
I am an absolute noob in the 3D printing world so after reading tons of reviews, watch YouTube videos and scrutinise internet forums about this topic, I decided to buy this on specifically. I am amazed and fascinated. The assembly is fairly simple. Instructions are clear and concise. Literally, in 30 minutes since I opened the box I was printing that cat that comes in the SD. I am loving it. I totally recommend it.
-keeps printer nearly dust free
-keeps temperature very stable
-looks dang good
Con ONLY ONE,
-watch your temperature if you close the enclosure during print!!!
I set my printer up to do an overnight print like I’ve done before but now I have a new cover and I zipped it shut, that was a huge mistake. The hotend got heat creep causing a clog and filament went everywhere but down. Birds nets!
So, great enclosure great value DO NOT leave it without some good ventilation.
Great product, perfect size and keeps the temperature just right while printing. Also has the peace of mind that it is fire resistant too
Caisson trs utile et adapt la CR10 (taille L)
Attention toutefois, la qualit des fermetures clair n’est pas non plus terrible, mais rien de trs gnant.
Je recommande si comme moi vous voulez un caisson pour votre imprimante sans prise de tte.
Love this, added in some LED strip lights too. There could be a better fit for my ender 3 V2 but I guess its generic. Keeps heat in well and stops the room from getting unbearably hot.
Great quality product – I highly recommend.
However, please bear in mind that this is a fit-all enclosure. It is probably a bit large for my Ender 3 and also changing the filament is an access problem as there is no leftside opening. Other than these minor niggles a fine product.
Sind wir ehrlich: Es ist halt eine Hlle. Aber sie ist durchdacht. Einmal aufgebaut (was sehr leicht geht), hlt sie eine Auentasche fr Zubehr bereit, auserdem gibt es mehrere clevere ffnungen von fast allen Seiten, inklusive einem Zugang fr die Verbindung zum Computer (wenn man das will).
Einfach aufzubauen, Drucker passt gut rein, sorgt fr eine gleichmige Umgebungstemperatur und verhindert zuverlssig Warping.
Einziger Kritikpunkt: Das Ding stinkt bestialisch nach Chemie in der Ersten Zeit. Am besten lsst man es eine Weile auslften.
Ansonsten ein tolles Produkt in ergnzung zum Ender!
Warping ( Ecken die sich lsen von der Druckplatte ), Abbrche beim Drucken, schlechte Qualitt, etc.
Nirgendwo bei YouTube oder irgendwelche schlaue Foren einen richtigen Hinweis.
Weil 3D Druck doch sehr praktisch ist fr Ersatzteile, Halterungen etc. habe ich dann noch ein Versuch gewagt und wieder investiert in mein Ender-5. Einen einzeln Hinweis hat gesagt : diese Hlle gehrt eigentlich zum Drucker.
Ohne viel Hoffnung, aber mit vollen Erfolg : kein Warping mehr und gute Druckqualitt.
Folgendes hatte ich gemacht ( gegenber der Standard )
– Neues Motherboard ( macht der Drucker leiser )
– BL Touch ( bessere Nivellierung )
– Neuen Extruder ( andere Hersteller )
–> alles ohne Erfolge
Neu dazu gekauft :
– Diese Hlle
– Neues Flexrohr ( Capricorn Bowden )
– Blue Tape (3M)
– Originale Extruder
Fr Alle die es fast aufgeben wollen. Das hier ist die Lsung.
Jetzt liebe ich mein Ender-5 wieder.
Great product that has upped my print quality massively! After a few issues with shipping the seller was extremely helpful and got everything sort ASAP. Will defo buy from them again.
This fits the Ender 5 plus very snugly. The tent itself is very, very large and would be overkill for smaller printers but you do have to slightly modify how the base install of the Ender 5 plus works before it will fit.
The directions tell you to have the spool heading outside of the back of the printer but the problem is it will not fit into the tent this way. You need to move the spool so it goes upwards from the back rather than out the back before it’ll fit.
The original tent had a broken zipper but they happily replaced it pretty quick. Overall I am very pleased with this tent.
Side note: Be sure to buy lights! This will make your entire work area dark, even with the front opened. I’m using a flashlight for now but will be installing lights soon.
Good size for my printer, keeps the temp constant and the cats and kids off the printer. Very pleased.
A lot of small print problems just went away after I started printing is a tent. I’d argue that this isn’t an optional piece of equipment. I like this tent way better that a rigid enclosure because it just takes a second to pull it down from the support structure and then another second to put it back when you have to do maintenance on your printer. In the case of my CR-10 I’d also recommending not pushing the table against a wall if you can help it. Being able to pull down the tent and walk around the back makes working on the hot end and extruder a breeze.
In the case of a CR-10 the filament roll normally sits on the control unit and feeds to the printer from the side. I did that for a while, it does just barely fit in the tent. Then I printed a bracket and some guilds so I could mount the roll on top of the printer and keep the control box outside the tent. I like that much better. The roll touches top of the tent, but everything works just fine.
As for stable temps, I am no longer having prints warp on the corners, adherence to the heated glass bed is amazing! It does cut down on noise, but not really all that much. It’s definitely quieter, but my main reason to get it was the stable ambient temperatures allowing me to have less wasted prints due to warping and other temperature related defects.
There was one small issue with the seams of the zipper, but the seller was very quick to respond and is shipping another tent (minus the poles) to replace this one. Very quick response, very satisfied with the entire process so far!