Duramax ECO 8 x 8 Hot-Dipped Galvanized Metal Garden Shed

Duramax ECO 8 x 8 Hot-Dipped Galvanized Metal Garden Shed – Anthracite with Off-White Trimmings – 15 Years Warranty





Green with Off-White Trimmings
Features
ECO 10 x 8External Dimensions (WxDxH): 322.1 x 242.3 x 196.1 cm Internal Dimensions (WxDxH): 307.8 x 223.3 x 191 cm | ECO 10 x 10External Dimensions (WxDxH): 322.1 x 302.3 x 196.1 cm Internal Dimensions (WxDxH): 307.8 x 283.4 x 191 cm | ECO 10 x 12External Dimensions (WxDxH): 322.1 x 362.7 x 196.1 cm Internal Dimensions (WxDxH): 307.8 x 343.3 x 191 cm |
Dimensions: | 175 x 72 x 12 cm; 80 Kilograms |
Model: | 0638801601517 |
Part: | 0638801601517 |
Manufacture: | Duramax |
Dimensions: | 175 x 72 x 12 cm; 80 Kilograms |
Fairly easy to erect with help,but found 1 or2 panels needed switching around. A few of the screws and washers in the roof leak slightly but the biggest annoyance was the incorrect dimensions the shed is not 8ft 8ft square as stated ,I made the base to those measurements but when erected its short by at least 4/5 inches so messes up with damp proofing but will get it resolved in the future. All in all I’m happy with it as it’s big enough to store gardening tools furniture and other equipme
As expected some of the holes don’t quite line up but easily remedied. Take care not to overtighten the screws. Tape for the ridge is pretty useless as you have to follow the contour of the roof sheets and if your shed is wider than 4′ you probably won’t reach the centre as the sheets will buckle very, very easily!
Don’t think you are buying a secure shed as you will never make it so. It would take a matter of seconds to rip a big hole with a tin opener and a single kick would probably put the doors in. It is little more than a rigid shelter but quite sound and sturdy once assembled and up to now, no signs of water leaks. Overall just what I expected.
If you are using it to store bikes etc I would suggest chaining them to a ground anchor.
Overall very pleased, I also have a yardmaster metal shed and it was a much bigger pain to put together than this one. This also looks so much nicer than most other metal sheds
Highly recommended for anyone of any skill level, definitely recommend at least 2 people to put it togethe
The shed looks perfect in my garden
True to size, colour etc.
It did take some time but just because there lots of screws/bolts but not hard. You will need 2 people and gloves as some egdes are a little sharp.
Overall great shed.
I managed to put this up on my own in 2 days. Though I would strongly recommend getting a friend to assist you.
Take your time and you can’t go far wrong, the instructions are for the most part easy to follow.
So far the shed hasn’t let any moisture in on my tools and it looks nice in the garden with tidy trims and finishes.
It’s been standing in the garden now for a few months. It’s withstood a heatwave, torrential rain and some strong gales coming of the hills. It isn’t weather tight (water comes in the bottom of the shed) but we fitted shelving to keep everything off the ground. If you have anything that needs to stand on the ground you may want to install a raised floor.
Main things to take away:
– Take your time and preparation is essential
– Trust the process
– The metal edges are sharp
– If placing by a fence, make sure there’s enough room to get a ladder behind the back
Overall, very pleased and would buy again (though hopefully won’t have to for a while). All that’s left to see is how waterproof it is!
Once opened it had pictorial instructions and a huge number if individual pieces that reminded us of a giant Meccano set.
The instructions were easy enough to follow though and everything fitted together exactly as shown, taking us a full day and a half to complete.
Once built the whole thing was significantly stronger and more robust than we had expected and the finished shed is of a surprisingly good quality for the cost.
Overall we are quite impressed.
The only complaint we have is that there were not enough of the m4 nuts to complete the last couple if panels so we had to run out to the local DIY on the Sunday morning to by an extra 10 to finish the job.
However the shed when finished is a really a good size and waterproof.
Would recommend using a grid to place the shed onto. We also used gravel to fill this and placed a concrete base around the sides. We also bolted the shed down, and it is not suffering in the recent high winds. Now we have installed an OCD floor and shelves it should last for a very long time.
Good price for the 10×8. We noticed the manual said 8 hours to build, to be fair it is, its all the screws. Actually the screws are okay, it’s the fiddly little bolts and there’s lots of them too.
Almost built ours and very happy with it so far. We already had a slab base.
It really helps to have 2 people as can be a bit fiddly. Also wear gloves, I didn’t and cut my fingers on the edges as very sharp, but my own fault as it does say too.
The instructions are very good and easy to follow, it takes you through every step.
You have a warranty for 15 years.
I don’t like the colour so I’m going to paint it next year.
4 because it’s worth every penny. Would have been 5 Star if there weren’t hundreds of screws and bolts.
Came well packaged and in a small tightly packed box. You can’t lift it as its heavy so carried the parts through bit by bit, took only 10 minutes.
If you are looking for a budget metal shed, I highly recommend and may buy another.
Finished product is great
On the plus side:
more than required number of screws, bolts, nuts etc supplied.
Easy to follow instructions
Lightweight panels which makes lifting easy
Relatively easy to manoeuvre once complete into the final position for fixing to the base
All but 8 holes lined up, although some needed a little encouragement
Really good value for money
On the minus side:
Had to drill 8 holes which didn’t line up
Very sharp edges – use gloves or spill blood
Some panels had a protective covering ( which is good), but it took some effort to peel off
Overall it took 2 of us 12 hours start to finish including checking all the parts before we started, which took about an hour due to my OCD needing to count all the screws bolts and nuts.
You will need 2 people as the panels are quite flimsy until they are attached to the top frame.
We used an Ecodeck base and then attached 18mm ply board as a base to attached the shed to.
Overall really pleased, and would happily recommend
This arrived quickly, but as it comes in 1 box it’s very heavy. This needs sorting as the 2 delivery guys who looked well built , really struggled to move it, even with a trolley.
Once I started to put it up which took 2 weeks on and off. The book is very thick and the instructions are very clear . Please be aware this shed isn’t fully square.
I built a wooden base before starting but for some reason it wouldn’t fit flush,
I had great trouble trying to fix the rood on as the holes wouldn’t line up.
I ended up unscrewing the ground screws and now it sits at an angle as the roof really wouldn’t go on when it was flush. You also need to be quite tall to finish the roof as you have to lean from the outside to the middle of the roof.
The doors on mine don’t close properly as there’s A gap at the top so it’s not water proof.
It’s cheap for a shed and it looks like it will last despite the problem I’ve had.
The box that arrives you look at it and cant imagine a shed could be in it, other than by the weight.
The day before we laid some slabs around what would be the where the shed will sit on (using the manual online) and then created a wooden frame (to screw the shed onto and raise it off the ground) using 45mm high by 90mm ensuring the outside edge of the wood lines up with the outside of shed as you don’t want rain running onto the wood. At the front of the shed where the door will be you will need something wider wood wise as there is a ramp for the door and this is wider that the rest of the shed so needs supporting.
So the weekend arrived and we started at 10am with the build… you need 3 people ideally, two to hold the bits together as you start to assemble. The bottom bars and side panels are fairly easy to do but no less time consuming due to the amount of screws and bolts that have to be used (make sure you dont do when its windy).
We then started on the upper frame and roof bars, these are slightly trickier but again patience and a bit of moving about to ensure you havent got a twisted stucture, which is easy to happen until you have everything but the roof on and you can shift it slightly about to ensure its straight.
Next the roof, starting at one end on one side it a bit more difficult and you will need some decent steps to reach and secure to the top roof bar. Lining up is important and if it doesnt line up go back a step an check the previous roof sheet as if the little holes at the end of the roof panels dont line up you will have an issue putting the final parts on.
The other side of the roof is slightly hard and you need to add some silver tape down the join as you put them on. The tape could be wider and better and you may want to use something better but if not it will do. Again lining up is vital and it can take a while to complete this part. The the top metal cover over the join has to be put together and screwed down. This was a pain as its not the best design and could have been made better as once part with less gap under it to let in any possibly rain. This is where the tape that was used on the join will be the 2nd defence so its important that was put on correctly. Screwing in the middle screws on the roof on this part is also a but tricky unless you have some high steps and someone to keep you steady.
That was the end of the first day at 7.30pm. We started the 2nd day at 10am on the doors and once done the doors are fairly easy to put together and then that just leaves the plastic edging of the roof to tidy it up.
Then put the doors in and you will then know if you are truly straight with your build as the rail will need to be inline on the base for the doors to slide correctly. Then you need to build a floor inside, now you dont have to but then you risk damp or rain getting under the shed. I went for 18mm OSB at around 20 a sheet and you will need 2 of those if getting 2.4×1.2m or you could using decking wood and created a decking floor inside. For both plus some 45x45mm wood to create the supports for the floor.
After all that it was done and i’m knackered but it was worth the build. A nice looking shed that hopefully will be still up far longer than the other wooden once i have in the garden.
Well first of all this is not just any shed, this is a metal shed and as such means no hassle painting it every year, this has to be the main perk of these things, it saves an awful lot of time in the long run and in all honesty its not that expensive for that it is, Its not bad value for money although i did notice that the price seems to vary every week or two for some odd reason!! Maybe worth watching it for a bit first to see if it drops 😉
Construction wise, this shed was an absolute nightmare to put up, and that is coming from an expert flat pack builder who loves ikea!! There are large diagrams to follow and its broken down in simple to do steps, my main issue was however that sometimes they were not always clear and in one part, the diagram was drawn so the bracket faced the wrong way, so we get two thirds of the way through it and have to reassemble some parts as the bracket was facing the wrong way!!My advice would be to not follow the diagrams religiously like we tried to, i was worried about it all being incorrect so religiously followed the lot…. well until the point we realised the beams were drawn the wrong way around!! Use your initiative and dont be too reliant. The parts are really well labelled and easy to find – and there are a fair few of them!! The steel beams/silver parts are embossed with the code so you may have to tilt it to the light to see the code. The rest of the codes are stickered on…..When built is seems sturdy enough and overall size is pretty good, a little low to enter so if you are tall, mind your head 😉 but it does the job and it looks good……..
Pro’s …..
good price for what size it is
sturdy enough
lightweight enough to build without he-man or she-ra
looks good
no yearly painting
comes with a 5 year guarantee against rust etc
has ventilation to keep things dampness free!!
Negatives
The edges of the metal are SHARP, and i mean sharp enough to cut through gloves unless you are wearing thick rigger type gloves, so PLEASE invest in a pair before attempting to put the shed up (i have a small scar as proof, a mate has a matching one and the hubby has a large one that had to be glued as a reminder too, and i was wearing gloves!!!)
The roof is a disaster zone attempting to do!! Following the instructions you put the roof on panel by panel, which is great and easy to do although reaching over to get the screws in the center was a bit chaotic. The main issue came with the fact that there is some waterproof taping you get to run along the seam of the central joins /peak of the roof, this is vital and it will leak without it!! Only thing is you have to lean across the roof to get to it and run it along the length of the roof, this was a nightmare as we were not tall enough, and resulted in a ladder having to be used in an l shape for safety and the shed getting dented at almost every position we used…. A few of the holes didn’t match up either, when you are up a ladder and are having to pull the whole side of a shed roof to align things its a little scary haha!!
We had a mismatch of screws!!!! For some odd reason we were given a large bag of screws we only needed a few of and nowhere near enough bolts that we actually needed, check your amounts first guys!! It cost us almost an extra 10 in bolts…… and that was without anchor bolts which you will also need to buy- 10 a box of 50 at screwfix…..dewalt- they are brilliant !!
No way is this shed easy to assembly in a short time, it takes about an hour to get all the bits out and sort them out into piles etc …. we did it over a few days, we had kids helping – teenagers, dont worry who always had gloves etc on! to hold things up else i think it would have took longer, if you can afford to hire someone to build it i recommend you do unless you have alot of patience or have time to do it all in a day or so!!I wish i had done!!
Handles are plastic and not that strong, thick plastic but still, security wise i would buy a hasp and a good padlock as added security if you are storing valuables in it.
Overall it looks good bar the dents in the roof >< and it is a good size and for the money you are going to struggle to get alot better, the fact that it is metal is a huge advantage as maintenance is going to be kept at a minimal,no rot to worry about and a 5 year guarantee is good although the fact that it is an american firm may cause issues or high shipping costs lol!! for the money that it costs you are going to struggle to get anything else as good to be honest, and we had looked! But check your parts etc before you start to build it, insure it isnt a return which is what i am suspecting mine was and all will be ok 🙂