eSUN TPU-95A Rainbow Filament 1.75mm, Flexible Multicolored
eSUN TPU-95A Rainbow Filament 1.75mm, Flexible Multicolored 3D Printer Filament TPU, 1KG Gradient Changing Multicolor Filament for 3D Printer, Rainbow Multicolo
From the brand
Filament 3D Printing Materials:PLA Plus, Matte PLA, Gloss PLA, Light Weight PLA, Super Tough PLA, Silk PLA, Rainbow PLA, Marble PLA, Wood PLA, PLA Glow in the Dark, ABS Plus, PETG, TPU, PA-CF, PVA, Cleaning Filament
Liquid 3D Printing Materials:Plant-Based Pro Resin, ABS-Like Resin, TPU-Like Resin
3D Printing Accessories: eBOX Lite Dryer Box, eVacuum Storage Bag, eSpool Spool Replacement, eCure Lite Curing Box
| Weight: | 1 kg |
| Size: | TPU-95A Rainbow |
| Dimensions: | 21.5 x 20.5 x 7.2 cm; 1 Kilograms |
| Part: | eTPU-95A175RBB1KG-EU |
| Colour: | A-Rainbow Multicolor |
| Batteries Required: | No |
| Batteries Included: | No |
| Manufacture: | eSUN |
| Dimensions: | 21.5 x 20.5 x 7.2 cm; 1 Kilograms |
| Reference: | eTPU-95A175RBB1KG-EU |
| Size: | TPU-95A Rainbow |
Took a little bit of tweaking to get this to print without stringing but once I dialled in it prints great!
Have printed multiple phone cases using this filament with no layer adhesion issues or bed adhesion issues.
I was concerned about printing in TPU as I have a Bowden Drive setup. But after a few quick tests, I found it to print superbly, and have no major issues at all.
There was a tiny bit of stringing – but I guess that is the down side of using Bowden feed and rubbery elastic material that I am guessing does not retract as well.
I printed at 220, with a unheated bed (ultrabase) @ about 40-50mm/s
Supports pop off easily, brim you need to trim with scissors or knife. Tidying up the stringing with a knife was quick and easy.
Einfach zu drucken und sehr einfach anzuwenden.
Gibt bei Belastungen etwas nach und ermdet dabei aber nicht.
Sehr angenehm anzufassen.
Etwas Stringing, aber mit einem Feuerzeug einfach zu beheben.
Achtung: nur vorgeheizt und getrocknet sind gute Ergebnisse zu erwarten.
Bought as a alternative to a more expensive brand.. I have found it dose not print as well and comes apart. I am a experienced with 3D printers and different filaments and this isn’t as good as some of the other products
Flexible and worked in my Dremel 3D45. Had a problem feeding at one point, but I suspect its just because the reel is heavy and the filament a bit tightly wound so my machine wasn’t able to pull hard enough to turn it.
Great flexibility with this product and strong with thin prints, I did have a little bit of stringing to clean up but otherwise great.
I’ve been using esun pla plus filament since starting 3d printing a couple of years ago but this is the first time that I’ve tried tpu in my latest Ender 3 s1 with direct drive.
It printed flawlessly and without any stringing first time by carefully following guidelines off the web. I will need to adjust the fill percentage as the model came out a little hard.
It does look a little messy on the reel but it fed without issues.
Recommended.
Quality is good, but then when you’re paying full price of 30 so I wouldn’t expect anything less. I had it print first time with no issues, I used it to print a neck seal for a havoc trooper from Starwars, as you can see I got a bit of stringing at the back do I’m sure there’s are changes I could make but overall I’m pretty happy with i
Great adhesion, semi flexible perfect for the job required, printed a nozzle for a vacuum cleane
Layer adhesion is amazing, beautiful blue colour with near no shrinkage. I used this to make a cozy, printed it in vase mode and it worked beautifully. Used this for a structural part and stringing is horrendously bad, but as a tpu it is brilliant. It comes down to what part you print and I never dialed my settings, so set them up!!! Will buy this again with out a doubt.
Although I’ve not had TPU filament before, I found the suggested temperature settings perfect and had a great print first time. I used a temperature of 230C with no heated bed. The colour really pops and is a nice light purple colour like I was hoping. The packaging was great, a vacuum sealed bag with silica gel in a box that included a leaflet with other materials that eSUN sell and their differences, useful for if I was going to get some more filament.
It worked out better than i could ever Imagine i did a few good prints and i am impressed