Spigen 2 Pack NeoFlex Screen Protector Film for Samsung
Spigen 2 Pack NeoFlex Screen Protector Film for Samsung Galaxy S23 Ultra
| Dimensions: | 15.82 x 7.44 x 1.27 cm; 30 Grams |
| Model: | AFL05943 |
| Manufacture: | Spigen |
| Dimensions: | 15.82 x 7.44 x 1.27 cm; 30 Grams |
| Origin: | China |
This is a great screen protector, I’ve used a few different types and were all poor. This one was so easy to apply after following instructions. A perfect fit and looks great. I highly recommend it. 10/10
My first encounter with the self healing protectors. Dont get any serious damage on the phone, but minor cuts and grazes heal over and become virtually invisible in a matter of hours. Confused me a lot in the beginning until i realised what was happening. Had this for a couple of months, does the job well.
It’s a little soft for my taste, i’ve had it for a few months now and i can see a lot of indentations in the film.
It’s good enough for me but just so other people know.
A cheap/simple, yet effective screen protector.
After a puppy chewed on the phone, leaving the protector scuffed and damaged, not once but twice, both time the display was unscathed so I decided to buy a second set of these protectors… couldn’t have asked for more really, easy enough to apply doesn’t affect image quality, fingerprint works perfectly fine and its strong enough to withstand most real world usage and even a puppy assault, while being cheap enough to replace when worn/damaged.
Never had fingerprints work with a screen protector of any sort on previous phones ( S8, S21 ultra). Perhaps the S23 Ultra has better scanner, however I am inclined to think it’s this screen protector. Decent protection, fairly easy to install if you’re used to these things and importantly for me fingerprint biometric works!
Easy enough to install and the process is quite forgiving. Certainly I managed it without any bubbles or issues. Unlike the video I removed my case first. Give it time and any residual lack of clarity will disappear within a few hours. It does change the feel of the screen, increasing friction slightly, and when the screen is off, there is a noticeable orange peel effect. This does not bother me as it is not noticeable when the screen is in use and it is doing its job of protecting the device from scratches. Would definitely use again.
Watched the installation video and followed the instructions exactly. Applied the screen protector and initially thought oh dear, results were blotchy and although the screen protector went on straight and fitted well, the finished result left me wanting to remove it and try again. The screen was full of blotches and looked terrible. However I left it on the phone overnight to see if it cleared and sure enough next morning, perfect finish no blotchy finish and my phone looked great.
So basically give it time, wait for it to dry out over time and you’ll be left with a great finish, hopefully.
Idk what others are reviewing like they can’t put the screen protector.
That’s not Spigens design fault or anything. It is the fault of the person because they can’t put it.
All u need just watch their tutorial and keep patience while installing.
They are easy to fit I don’t know how people get in such a mess with them just follow the instructions and use plenty of spray and wet your hands, dripping actually the weter the better.
The only reason I am disappointed in this screen protector is I used my stylus to take some notes. Now I can read my writing on the screen. It has actually left an imprint of my writing in the gel so I can see it when the light reflects. It has ruined the whole look of the screen when it’s off. You can’t see it when the screen is on, but turn that screen off and it’s a mess you can make out the words. I have had other gels screens and have never had is problem before. I love the easy application of a gel screen and the fact you get more than one chance to line it up but i can put up with my screen looking like this. I will be looking for a replacement and it won’t be this thin gel one. I think it’s just too soft.
Probably perfect for normal use but be careful.
It is easy to apply if you watch the video but the protector itself, is, as others have said maybe a few mm shy in width, but your cover protects too. Narrowly misses out on 5 stars because of this.
I was then at the dreaded removal of the protector from it’s backing. To avoid damage, I used a very sharp small knife to slowly lift one top corner and left it in place on the side while I sprayed my fingers with the included solution. I then noticed a little dust spec of 2, back to the sticker. Re-wet hands and then very slowly peeled half of the protector away, and sprayed. Applied 2 small sprays to the phone screen and then carefully peeled the rest of the protector away and sprayed the rest of it. Lined it up carefully on the phone, slid into position gently and then pressed down. Finally, gently squeegee’d from the centre to all edges to push out the fluid and the protector stayed in place. For the edges, I also used the included cloth to finish off. Phew, looked OK …… well, apart from 2 very small specs that are trapped. However, only visible in certain light/angles and when the screen is off 🙂
I left it to cure/dry in a warm place for an hour or so ……. then the acid test, re-fit the Spigen Tough Case. This is where I’ve had real issues with screen protectors on curved edge screens, as they normally lift the protector …… NOT THIS TIME, happy chappy 😀
Screen responsiveness and fingerprint reactivity, can’t really see any difference, so all good.
I ordered these after having a terrible experience with the ‘Milomdoi 9H’ screen protectors.
In comparison, these are far easier to install and do not shatter (They are not glass).
My only feedback (4*) is there should be more spray. I had to be very conservative to leave enough for the second screen protector.
However… There’s always a catch , whilst this is the easiest (non glass) screen protector i’ve used in some time, it does leave an “orange peel” effect , those familiar with vehicle paint will know what i mean here, but i’ve attached an image for those who are not. Essentially, reflections are not perfectly flat under lighting, and gives an impression of the surface of an orange.
Disappointing, but, it does the job.
Note : Slightly smaller in width and length than other protectors for the S23 Ultra , BUT , When used with a case, doesn’t matter.
This screen protector is super easy to install as it is a wet install. You get a small bottle of liquid spray and you first clean your screen, use the dust stickers, then spray the protector with the liquid and slide it around the screen until it fits. Use the included squeegee to squeeze the remaining liquid out and let it dry for 3 mins. After that, you’ll get the best touch screen experience you can possibly have with a screen protector. There is zero screen lag, no gap between the screen and the protector, the typing experience is fluid and smooth, the finger print sensor works as though there is no protector on the screen and overall, its an excellent product.
If you get any dust after install, simply lift the protector, spray some more liquid, remove the dust with your finger and squeeze the liquid out.
Hats off to Spigen on this one.