Vandicka 2 PCS Stainless Steel Woven Wire Mesh Sheet 25 x 25
Vandicka 2 PCS Stainless Steel Woven Wire Mesh Sheet 25 x 25 cm Square – Air Brick Vent Mesh Cover for Rodent Proof Insect Pest Control – 20 Mesh 1mm Hole Metal Wire Gauze – Drain Cover Mesh
Weight: | 180 g |
Size: | 25cm X 25cm, 2 Sheets |
Dimensions: | 28.6 x 24.6 x 2.4 cm; 180 Grams |
Model: | DBL-03 |
Part: | DBL-03 |
Colour: | Silver |
Batteries Required: | No |
Batteries Included: | No |
Manufacture: | Dipoli |
Dimensions: | 28.6 x 24.6 x 2.4 cm; 180 Grams |
Size: | 25cm X 25cm, 2 Sheets |
This mesh is easy to use and (does what it says on the tin).You do need a good pair of tin snips if you are going to want to cut it. Ideal for covering vents
Ordered on Monday arrived Tuesday good service.
Easy to fit just used clear sealant to stick it over the air bricks, has stopped the wasps getting in.
A lot cheaper than getting pest control.
This was a life saver. I had slugs crawling up to the eaves of the house and getting into the vents of my bathroom extractors, ending up in my shower, it was like a horror story! I’ve never experienced anything like this before. These are easy to cut with tin snips and I siliconed them to cover the extractor vents. I can now go into the bathroom with confidence.
I bought this wire mesh for miniature making
It is thicker than I thought but can be cut with large scissors.
I don’t find it very easy to bed into shape so I would probably try for something thinner than this
But the quality is good for what it is
This was purchased to block a gap in the brickwork of a conservatory where a cat flap had been fitted after an infestation of mice. The mesh covered the gap adequately and was easy to attach. Hopefully, it will solve the problem.
After hearing some scratching noise in the kitchen one Sunday morning I found there was a mouse inside the extractor hood over the hob. Not just in the hood, but actually in the fan unit itself. Using a torch I could see his little greasy face looking back at me. The only way he could have got in is through the vent outlet, about 7ft above the ground on a flat wall, behind a plastic grille. I eventually got him out by unclipping the fan case and managing to squeeze a few fingers in until I felt something soft and squidgy, pulled it out into a bucket. I was about to release him into the field behind but he jumped out the bucket himself, over the fence.
I needed something that allowed air out and kept random mice and insects outside. This mesh was perfect, and after a bit of trimming with stout scissors to cut it to size it fitted nicely behind the plastic grille. Hopefully I wont experience any more chewing of my extractor fan and with the mesh being stainless steel, it shouldn’t rust. You’ll have to do better than that, mousey!
It was brilliant but it did show 4 bits but was only two and I got it because I have air vents on my boat so I have had to buy another pack
I used this for both an airbrick and to fit to an air extrator fan, both of which were entry points for flies. It is easy to cut, has a relatively fine mesh and, most importantly, kept out the flies.
Adhesion is not applicable.
Thickness is as I chose
Great value for money, delivered.
I bought it to protect the oil cooler on my toy car, keep the midges out of my caravan, and for stock..
I kept having to clear leaves from the hole to the air vent for my log fire. This did the trick. I bent it very slightly on the edge and it was a perfect fit them. The leaves now do not go down the hole and collect. They stay on top and are blown away by the wind. Great.