Comgrow 3D Printer Enclosure Fireproof and Dustproof Tent
Comgrow 3D Printer Enclosure Fireproof and Dustproof Tent for Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 Neo/Ender 3 V2 Neo/Ender 3 S1/Ender 3 S1 Pro, 3D Printer Cover Storage 635x535x750mm
From the brand
| Weight: | 2.29 kg |
| Size: | M |
| Dimensions: | 75 x 63.5 x 53.5 cm; 2.29 Kilograms |
| Part: | US4-GGHZP |
| Batteries Required: | No |
| Batteries Included: | No |
| Manufacture: | Creality 3D |
| Dimensions: | 75 x 63.5 x 53.5 cm; 2.29 Kilograms |
| Reference: | US4-GGHZP |
| Size: | M |
Its recommend that if your prints are constantly warping or coming away from the print bed that there is a chance the ambient temperature is to blame.
This upgrade helps to remove this variable from the list of possibilities.
Just bear in mind that this is quite large as it must house the whole printer with some spare room to spare.
I purchased this enclosure as I was experiencing adhesion issues when running my Ender 3 v2 Neo a cold room; this seemed to offer a cheaper solution that turning up the heating. Well it works better than I expected; where in the past I would have needed to print on a raft I am now, in most cases, able to print abs and petg without any adhesion constructs.
Although it requires a bit of wiggling to get my Ender 5 Pro in the medium sized enclosure, once in I found there was plenty of room to setup and use the printer.
It is awkward to change the spool but as that’s not very often I don’t mind. It overlaps the little ikea table every one seems to use by a few centimetres but not enough to cause a stability issue.
Overall I am very happy with it, as the printer is in an outbuilding I had so many failed prints when the temperature dropped. Well, not anymore my prints are so much better quality and not one failed print. With a blanket on top the temperature stayed around 25 C.
Had trouble with failed prints in my house due to drafts and temperature fluctuations. This solved these but I did have to modify it for my printer. Should be OK with an Ender though.
Does help with adhesion but mainly helps stop the dust in the air produced by the printer. Not sure what it was with my Ender 3 V2 but after few hours it always seemed to feel dusty in the air when in use, after all there is super fine partials produced by the printer. Now the printer is inside this enclosure it definitely feels better in the room. It has cut down the “feel” of the dust in the air/better air quality.
I also run an air purifier close to the enclosure to help also. A must if you have an Ender 3. Can’t give it 5 stars due to its size. It is quite big, it could have been slightly smaller, it’s also a dust magnet on the outside.
Will update this review further down the line.
For a small its big.
I have an ender 3 inside.
So easy to assemble and fit cover on.
Holds temp well i have a digital thermometer and its 36 most times.
Would recommend put a light in it as its dark to see inside.
Worth the price and good value.
Im happy with i
I bought this for my Ender 3v2. It was bigger than I expected but it should help with better prints. Easy to assemble once I worked out the cover alignment. The power lead aperture is on the wrong side but that’s no problem. There’s lots of room inside and although it looks quite chunky in the room, actually it’s not vastly bigger than the dimensions of the printer. It could do with being a tad shorter but it’s perfectly livable with. As a 3D printer enclosure it is excellent value and will fit many printers. I recommend it.
I used with a Prusa Mk3. It is bigger than you actually need for such a printer, but it does mean that you have easy access for maintenance etc
The material is very odd, it’s almost sticky. The listing claims it is fireproof, I would be SHOCKED if that is true.
Easy to assemble and seems sturdy. Fits my Creality Ender 3 in it no problem. A useful pouch on the side and slot for allowing mains plug out as well. I recommend it even though it is a tad pricey.
The enclosure unit is expensive for what it does, also there are many issues with the seals on the unit I received resulting in having to tape it up. Overall I would probably do one in perspex next time to ensure the seal was better would recommend it for a beginner.
Luckily I have the room for it and have built a dedicated table for it.
This is massive, but for me its worked out really well as My Ender 3V2 is heavily modified. and its given me the room inside the tent to accommodate all my mods, custom top mounted spool holder for direct drive, keyboard for octoprint my printers rarely off so its also allowed me to store all my PETG inside at 35’c 22% humidity, which is what my tent seems to levels out at when in use and zipped up.
The window takes a while for the creases to fall out, but they will making the window much easier to see through.
Its very easy to assemble, the quality of mine is very good, all stitching and zips are well constructed in the right places of corners.
It has created a stable temperature printing environment, has also helped me to prevent some corner lift/warping on large surface area, longer printing models as i print in PETG Nylon and CF filaments.
I really like the enclosure, bought 2 now for my machines. I get better prints because the heat is contained and more consistent where my printers are in drafty garage.
It’s just a shame the opening flaps position is such that operating the printers controls is awkward. Would have been better to open up the front and not the side.
Fits printer well with plenty of room for access and spool. Feels durable and good quality. Comparable to ones twice the price. Would recommend using side access flaps to pipe in ventilation for main board and power supply as it gets warm in there. Perfect for printing ASA/ABS or just keeping dust off the printer. Seems to cut out noise well, but is dark inside without some LED lights fitted to the printer (which is very easy to do).
As the nights get colder now, overnight prints are having delamination. Bought the kit to keep the heat in, and it works perfectly well. Improved print quality dramatically. The sound reduction isn’t massive, but it does make a noticeable difference.
I, like you, make things myself, hence we are printer owners. The temptation is therefore to build your own enclosure, however given I have limited time I decided to try this ready made one.
There isn’t much to fault. It goes together easily, is as sturdy as you’d expect and has openings in all the right places (this review is for the large version for a CR10S Pro). There’s even an outside pocket for all those tools you keep losing.
Be aware that (at time of writing) the picture on the Amazon site has the depth and width dimensions swapped – it’s 750 mm front to back, see the picture attached to this review.
I am an absolute noob in the 3D printing world so after reading tons of reviews, watch YouTube videos and scrutinise internet forums about this topic, I decided to buy this on specifically. I am amazed and fascinated. The assembly is fairly simple. Instructions are clear and concise. Literally, in 30 minutes since I opened the box I was printing that cat that comes in the SD. I am loving it. I totally recommend it.
Great quality product – I highly recommend.
However, please bear in mind that this is a fit-all enclosure. It is probably a bit large for my Ender 3 and also changing the filament is an access problem as there is no leftside opening. Other than these minor niggles a fine product.
Great product that has upped my print quality massively! After a few issues with shipping the seller was extremely helpful and got everything sort ASAP. Will defo buy from them again.