FatMax® Tenon Back Saw 360mm (14in) 11 TPI
FatMax® Tenon Back Saw 360mm (14in) 11 TPI
Step 1:
You can achieve a good cut without tearing out by marking the line with a knife, not with a pencil. Always saw on the bad side (cut side). If you are unsure, leave some space. If necessary, protruding wood can be planed subsequently flat.
Align the good side upwards so that splinters or torn areas are covered at the bottom. This is particularly important when working on ceiling or floor coverings, such as laminate.
Step 2:
Start cutting at the edge farthest away from you. Hold the saw at an angle of approx. 30° to the surface. Use the thumb nail of your free hand or a remnant piece to position the cut to the bad side. The first stroke should be more like a light pull to create the cut line (notch).
If the saw is correctly in the notch, continue to saw at an angle between 45° and 60° to the surface.
Step 3:
Hold the handle firmly but relaxed. Keep your wrist, elbow and shoulder in line with the saw blade and marked line. You should also keep your head and eyes in line with the cut.
Use the whole length of the saw with constant, non-rushing movements. The speed can be increased by lowering the handle once the blade has slipped half through the material on impact. Lower the handle when pulling. Slow down the pace when the saw leaves the marked line. Correct your standing position and carefully try to restore the mark.
The saw sound shows you the end of the cut. Support the sawn piece of wood so that it does not fall off uncontrollably.
| Weight: | 259 g |
| Size: | 350 mm |
| Dimensions: | 46.5 x 14.5 x 3.1 cm; 258.55 Grams |
| Model: | 2-17-201 |
| Part: | 2-17-201 |
| Colour: | Multi-colour |
| Pack Quantity: | 1 |
| Batteries Required: | No |
| Batteries Included: | No |
| Manufacture: | STANLEY |
| Dimensions: | 46.5 x 14.5 x 3.1 cm; 258.55 Grams |
| Quantity: | 1 |
| Size: | 350 mm |
Stanley 2-17-199 - Scie À Dos Gamme Fatmax 300mm
Bonjour
J’ai test sur une boite pour les angles autre que les angles a 45 ,et sa ne correspondais pas .J’ai t oblig de le renvoy ,sinon sa coupe trs bien,je recommande
Ok apart from delivery.
Good product. Replaced existing worn out saw. Surprised it survived being dropped over 6 foot gates onto block paving by delivery driver. I suppose that’s a good test of its strength!
Great quality, sturdy saw
Very impressed by this saw when I used it to cut some joints that needed to be very accurate. It has a good weight to it, cuts well and is easy to control.
Stanley, has been a great quality product for many years.
This tennan saw is Good price and good quality. If it lasts as long as the Stanly it is replacing
That will be another 40 years and it will see me out. This is a name I have relied on all my life. I have many Stanley products from a simple knife to garden a garden spade . Would recommend .
.
Bit heavy, but razor sharp
This is larger than my old tenon saw, which is near retirement after 30yrs, and a bit heavier and longer. The thing is razor sharp, so watch a) your fingers, and b) the rate of cut. It cuts at a rate of knots through the roughest of timber.
Could do with a proper blade protector, instead of the cardboard sleeve, it wouldn`t have cost much to provide it, my other saws have them.
Bie
J’avais une scie dos bas de gamme STANLEY d’une longueur de 300 mm,trop courte pour la boite onglet de la mme marque. Elle n’a pas coup longtemps. J’opt par une longueur plus grande et une gamme au dessus. J’espre ne pas tre du.
Bon produi
Bonne prise en main, coupe bien, cela permet d’avoir des finitions propres notamment pour les plinthes. Seul bmol elle est un peu courte pour tre confortable avec une bote onglet. Cela aurait t parfait en 400mm.
Top Säge, könnte aber leichter sei
Ich bin mit der Sge sehr zufrieden, sie ist sehr verwindungssteif, arbeitet klasse….
Meines Erachtes knnt das Gert nen bisschen leichter sein, aber das empfindet ja
jeder anders.
–> Kaufempfehlung!
Scie dos rigide pour coupes d’onglet et finitions.
Lame de 0,86 mm d’paisseur.
Trs bonne prise en main grce sa poigne antidrapante.
Deux modles sont proposs en 350 mm : une denture JetCut “triple biseau” 11 dents/pouce et une denture universelle 13 dents/pouce. Il s’agit ici du modle JetCut.
Rapport qualit/prix correct pour un travail soign sur petite section.
For a tenon saw look no further. For precision Mitre cuts this will be loved.
I have the long Fat Max too and like that saw, this tenon saw is extremely sharp and cuts through wood simpler than you will get with any other handsaw. Every cut out I made for joints this saw over-cut and no matter how careful I was. You only need to move the saw a bit and it has cut a cm. If you get the cut perfect, you will have to move the saw carefully otherwise any contact with the wood will cause an over cut. Straight forward cutting like on a mitre board – it doesn’t get any better.